Originated From
AOL Search

How to replace rear disk brake pads on 2009 dodge grand caravan

Liked this question? Tell your friends about it

2 Answers

Order by
Oldest to Newest
Newest to Oldest
Votes

1.Park the Caravan on a relatively flat and paved surface. Do not apply the parking brake. 2.Place the Caravan in gear and then place a wheel chock in front of one or both of the front tires. 3.Crack the lug nuts to both rear wheels loose 1/4 turn, with the tire iron. 4.Raise one rear panel with the jack, and then support the Caravan with a jack stand safely and securely. Do not use the jack as asupport for the minivan. Repeat this step for the opposite side. 5.Remove the loosened lug nuts, and then remove the wheels. 6.Locate the caliper on top of the rotor. Remove the two caliper guide pins, using a ratchet and socket. 7.Pull the caliper off of the rotor, caliper bridge and pad assembly. Rest the caliper on top of the suspension. 8.Remove the pads from the caliper bridge, and then remove the caliper bridge bolts only if you're replacing the rotors. If not, proceed to Step 12. 9.Remove the rotor. It may be stuck onto the hub or internal parking brake shoes. If so, use a dead-blow mallet to shock it free and then remove it carefully. 10.Clean the new replacement rotor with brake clean spray, wipe it dry with a shop rag and then place it on the hub assembly. 11. Replace the caliper bridge and bridge bolts. Tighten the bolts using an appropriately sized socket and the torque wrench, set to 90 to 100 foot-pounds. 12. Apply a coat of brake silicone to the caliper bridge contact points where the backing plates of the pads are seated. 13. Place the shims (supplied inside the pad set) onto the backing plates of the pads, if applicable. Some pad sets may have the shims already staked on with external rivets. 14. Place the pads into the caliper bridge. 15. Compress the caliper piston, using a large set of channel locks, until the piston is completely seated inside the bore. Replace the caliper and align the guide pin bolts through the caliper and into the knuckle. Tighten the bolts, using an appropriately sized socket and the torque wrench, set at 50-foot pounds. 16. Replace the wheel and lug nuts. Tighten the lug nuts snugly with the tire iron while holding the tire. 17. Repeat the procedure for the opposite side. 18. Lower the Caravan, and then re-tighten the lug nuts using an appropriately sized socket, and the torque wrench, set at 100-foot pounds. Tighten them in a star pattern and not in a circular pattern. 19. Pump the foot brake pedal to return the caliper pistons to their original position. This will seat the pads against the brake rotors. hoping this can help you.

Professional Diagnostic Tools, Car Key Programmers, Mileage Correction Programmer for Dealers, Fault Code Scanners, ECU Chip Tunning Tools. http://www.chinasinoy.com

I've seen some 2009 dodge caravan on Tradingpost. Maybe you can ask the guys who owns them. or other types of caravans.

Related Questions

Other people asked questions on similar topics, check out the answers they received:

Asked: Waiting for mechanic to certify repair

how long does it take to certify a transmission repair. It has been awhile since I dropped my car off and what was supposed to be a week has turned into almost 3. Now I am told the mechanic has to ...

Asked: Youtube.com door handle repair for my 2012 chevy ...

youtube.com door handle repair for my 2012 chevy silverado

Asked: Car pulls to the rt. on a 2004 r volvo during ...

car pulls to the rt. on a 2004 r volvo during acceleration. Car has been align and tires are wearing even.

Ask a Question... We'll forward it to people who know

More Questions

Wireless Charger Charging Pad?

There are many wireless chargers on the online shop. of course they can charger many electronic devices,include ipad,iphone. I hope vipstech's answer can help you.

Bleed front brake

Depends on the model. Sportsters have a small reservior that goes with that Sport front end (it ain't a narrow glide). Big twins get a Narrow Glide or Wide Glide front end, and a Springer front end if you got lots of steel bridge grates to cross. Sportster. Open the cylinder and set an HD ...

Rebuild brake pad

Try taking it to a local AAMCO (http://aamco.pwserve.com/storelocator/). They should be able to help you.

How to change brake pads on 2002 nissan quest

I assume you've never swapped out pads before. If so, I recommend that you find someone who has to show you how. While a fairly simple job, there are pitfalls and brakes are too important to not realize you made a mistake. Once you've helped someone do it right, you'll have the procedure down ...